Home --- News --- Why Flexible MMO Titanium Ribbon Anodes Finally Solved the Cylinder-Shielding Problem in LargeDiameter PCCP Water Mains

Why Flexible MMO Titanium Ribbon Anodes Finally Solved the Cylinder-Shielding Problem in LargeDiameter PCCP Water Mains

Nov. 18, 2026


For four decades, the prestressing wire that holds a four-meter water main together was the one piece of steel cathodic protection could not reach.

MMO Titanium Anode Field Series  ·  Baoji Titanium Valley  ·  Nov. 18, 2026

 

A 2.4-meter PCCP main pushes 180 million gallons a day through a corridor with no spare road to dig up. Its strength comes from a steel cylinder wrapped in 1,500 MPa prestressing wire. That wire is also the part that fails — and for most of the last forty years, the honest answer a cathodic protection engineer could give the pipe owner was: we can protect everything around your pipeline except the wire.

1. The Problem: The Strongest Part of the Pipe Is the Part Current Cannot Reach

Strip a PCCP line down and you get four layers: a concrete core, a welded steel cylinder (0.5 to 1.6 mm), a helix of high-strength prestressing wire wrapped at 5 to 15 mm pitch, and 25 mm of roller-applied mortar or 50 mm of cast concrete on the outside. The cylinder is the load-bearing membrane. The wire is the muscle that keeps that membrane compressed. And the cylinder is also a Faraday cage.

That is the whole problem, and it is geometric before it is electrochemical. Current from a remote anode bed does not wrap politely around a 2.4 m steel can. It finds the nearest steel — the cylinder — and stops there. The wire on the anode side gets a share of the current through the mortar. The wire at 3 o'clock, on the far side, gets almost none. So a deep well 25 m away does a beautiful job of protecting the cylinder wall, and quietly starves the wire that actually holds the pipe together.

The false reading

Here is the part that hurts. A potential survey taken at grade reads −0.95 V versus Cu/CuSO₄. The owner sees a protected pipe. The report says "within criterion." But you measured through 25 to 50 mm of concrete, on the near side, on a pipe whose far-side wire is sitting at −0.55 V and losing section every wet season. This is why excavation reports keep finding wire breaks clustered at 3 o'clock and 9 o'clock — and why they keep finding them in mains that passed every annual survey.

Why every traditional answer fell short

Table 1  Why conventional CP architectures fail on a large-diameter PCCP main


Anode type

Why it fails on a large-diameter PCCP main

Deep-well MMO tube

Reaches the cylinder, never the far-side wire; needs drill space you do not have under a live transmission main

Sacrificial zinc ribbon or mesh in soil

Consumes itself in 5 to 10 years; cannot hold the current a 7.5 m circumference demands

Point anodes in a ring around the pipe

−1.3 V in the near field, −0.6 V on the far side; over-protects one quadrant while under-protecting another

Conductive polymer ribbon

Right layout, wrong material; ages, swells, hits a current ceiling, 20 to 25 yr practical life

Recoat and repair only

No excavation access on a live main, and it does nothing for wire corrosion already underway

What the owner needed was not more current. It was the same current everywhere — the same milliamps at 12 o'clock as at 6 o'clock, for 30 years, from a strip that fits into a 300 mm trench beside a pipe you cannot shut down.


2. The Bottleneck: A Design Window Narrower Than the Tolerance

PCCP sits between two cliffs, and both of them are electrochemical. The upper cliff is hydrogen embrittlement: high-strength prestressing wire, especially the low-ductility wire drawn before the mid-1980s, will crack under over-protection. Field practice holds the wire between −0.85 and −1.00 V versus Cu/CuSO₄; push more negative than that and you are no longer protecting the wire, you are pre-loading a failure. The lower cliff is the −0.85 V criterion itself, which has to be met at every point on a 7.5 m circumference, not just at the test station.

The window between the two cliffs is about 150 mV. A point anode produces a gradient that blows through both of them inside the same meter of pipe. That single sentence is the entire engineering case for a distributed anode.

Three things had to be solved at the same time, and none of them could be solved alone.

Uniform, low-output current around a 7.5 m circumference. PCCP current demand is tiny — 0.1 to 1.0 mA/m² of wire surface — because the coating is dense mortar with resistivity in the hundreds of ohm-cm. A powerful anode is not the answer. A predictable, continuous one is [7].

A coating that survives being bent. IrO₂-Ta₂O₅ brushed onto 0.635 mm titanium strip, sintered at 420 to 480 °C, then coiled onto a 152 m spool with a 50 mm bend radius. Most labs crack the oxide at the bend. A cracked oxide is a hot spot, and a hot spot is a burn-through at year six.

Retrofit with zero excavation. You are not digging up four kilometers of live main through a city. The anode goes into a 300 mm trench alongside the pipe, or onto the pipe at the plant, and then has to sit there for 30 to 50 years with an IPX8 splice every 150 m.

For years the specification lived in AWWA C304, in a Chinese national standard, and in a handful of imported brands. Domestic shops could roll titanium strip all day long. Almost none of them could keep the oxide alive on it.


3. The Baoji Fix: A Cluster-Scaled Breakthrough

Baoji — the Titanium Valley — did not solve this in one factory. It solved it as a cluster, the same way it solved the tank-farm ribbon a decade earlier. That matters, because the three bottlenecks above live in three different buildings.

What the lead houses pooled:

· Substrate discipline: TA1 / GR1 cold-rolled strip, controlled Ra, oxalic etch, zero ferrous stringers, deburred edge so the coating never starts from a micro-crack.

· Coating system: IrO₂-Ta₂O₅ thermal decomposition, 8 to 20 g/m² noble loading, multi-pass brush plus 420 to 480 °C sinter, continuity checked every 10 m.

· Geometry standard: 6.35 × 0.635 mm and 12.7 × 0.9 mm became the de-facto domestic sizes, with a bend radius of 50 mm or less.

· Joint know-how: Ti-Cu transition crimp, silver braze, epoxy encapsulation, heat-shrink, IPX8 rated for decades of burial.

· Layout rules: paired ribbon at 300 mm from the pipe wall, one run on each side, phased current, 17 to 42 mA/m baseline, 30 to 50 year design target.

That last rule is the actual answer to cylinder shielding. You cannot push current around a 2.4 m steel can. So you stop trying — and put an anode on both sides of it. The far-side wire then has its own current source 300 mm away, and the cylinder stops being a shield and goes back to being a membrane.

What Shaanxi Ruifuxiang (RFX) brought to the table:

· Certified GR1 strip on the dock. ASTM B265 substrate with MTC EN 10204 3.1, delivered with the surface finish the coaters needed — no re-grind, no contamination [5].

· The incoming-inspection loop for several local coaters. Ra check, chloride residue check, edge-burr check. Boring work that decides whether a 152 m spool fails at year six.

· Roundtable work on ribbon open area versus backfill contact. This is the variable that decides whether the current field stays uniform over 4 km of main, not just at the test station.

· Spool and splice engineering. Custom widths plus 150 / 152 m spool packaging and the spool-to-spool splice sequence, so a crew lays a whole transmission main from continuous coils with no mid-field joint.

· Packaging line discipline. Vacuum seal within 24 hours, no ferrous cross-contact, same-heat reorder when a project moves into its second phase.

What the cluster gave back:

Table 2  What the Baoji cluster released downstream

Deliverable

Result

Shared process baseline

Approximately 12 to 15 mesh / ribbon / wire process patents released downstream at cost

Domestic ribbon life

From "experimental, 8 to 10 yr" to 30 to 50 yr, with 30 yr as the contractual floor [1]

Unit cost

Down 30 to 45% against imported flexible anode

Installation cost

Down 20 to 35%: no anode bed, no deep well, a 300 mm trench alongside the pipe

Lifecycle CP cost

Down 40 to 60% over 30 years, counting drilling, anode replacement and survey labor

Cluster-level saving

Several hundred million RMB in avoided re-work and import substitution across the water segment

Export margin

18 to 25% on coated ribbon versus 8 to 12% on commodity titanium strip

Put plainly: the cluster stopped selling metal by the kilo and started selling protected kilometers. A pipe owner who used to budget a full anode-bed rebuild at year 15 now budgets a survey at year 15 and nothing else.


4. Where Flexible MMO Titanium Ribbon Goes

Table 3  Application map for flexible MMO titanium ribbon anode

Sector

Application

Large-diameter PCCP water mains

Both-side ribbon layout at 300 mm offset, 17 to 42 mA/m — the original use case behind this article

Raw water and cooling water lines

Power plants and nuclear stations, intake and discharge headers [6]

Dense urban transmission corridors

No space for anode beds; ribbon goes in the same trench as the main

Steel water transmission mains

Coating-aged segments where deep wells are impossible

Oil and gas tank farms

Tank-bottom concentric-ring ICCP, the case that started the series

Marine outfalls and jetties

Ru-Ir variant for chloride and splash zones

Concrete structures

Bridge decks, wharf decks, water tanks — ribbon and mesh hybrid

Industrial process

Electrochemical oxidation, desalination, process vessels

The market math is simpler than most people expect. Every kilometer of 2.4 m main needs roughly two kilometers of ribbon, one run per side. A single 10 km transmission job is therefore a 20 km anode order — about 130 spools, plus splices, plus a monitoring loop. Multiply that by the aging PCCP base in North America, China and the Middle East, and by the fact that a 30-year design life has now become the default specification rather than a premium option, and this stops looking like a niche product. It looks like a retrofit market with a multi-decade tail.


5. RFX Production Size Table (Flexible Ribbon Anode)

Table 4  Standard and custom flexible ribbon anode sizes

Model

Substrate

Width (mm)

Thickness (mm)

Roll length

Coating

Output current

Design life

RFX-R1

GR1 / TA1

6.35

0.635

150 / 152 m

Ir-Ta, 8–12 g/m²

17 mA/m

50 yr

RFX-R2

GR1 / TA1

12.7

0.9

150 / 152 m

Ir-Ta, 10–15 g/m²

34 mA/m

25–50 yr

RFX-R3

GR1 / TA1

12.7

0.635

150 / 152 m

Ir-Ta, 12–18 g/m²

42 mA/m

20–50 yr

RFX-R4

GR1 / GR2

12.7

0.9

150 m

Ru-Ir-Ta

40–60 mA/m

20–30 yr

RFX-R5

GR1 / TA1

25.4

0.9

100 m

Ir-Ta, 15–20 g/m²

60 mA/m

30–50 yr

Custom

to drawing

5–25.4

0.5–1.0

50–500 m

project-spec

10–86 mA/m

20–50 yr

Substrate: ASTM B265 Gr1 / TA1, with MTC EN 10204 3.1. Coating: IrO₂-Ta₂O₅ for soil, freshwater and concrete; RuO₂-IrO₂-Ta₂O₅ for seawater. Bend radius 50 mm or less. Joint: IPX8 sealed Ti-Cu transition. Standards: GB/T 33637-2025, AWWA C304, NACE SP0169.

Selection rule. A main of 1.6 m diameter or larger takes 12.7 × 0.9 ribbon on both sides at 34 mA/m. A 3 to 4 m main takes the 25.4 × 0.9 wide ribbon at 60 mA/m, again on both sides. Coating-aged or high-resistivity segments take 12.7 × 0.635 at 42 mA/m. And never sign off a layout without checking the −1.00 V ceiling in the near field — the anode that saves the far-side wire and cracks the near-side wire has solved nothing.


6. Shaanxi Ruifuxiang — The Substrate Behind the Ribbon

Shaanxi Ruifuxiang Industry and Trade Co., Ltd. (Baoji, 2017) is the quiet layer under a good share of Baoji's MMO ribbon output. The company runs anode-grade GR1 / GR2 titanium strip, wire, mesh, tube and plate across a full non-ferrous catalog (Ti, Zr, Nb, W), and it is the first phone call a coater makes when a spool has to be right the first time.

· Surface-ready substrate: controlled Ra, oxalic etch, deburred edges, vacuum seal within 24 hours, no ferrous cross-contact anywhere on the line.

· Fastener and component line: titanium bolts, nuts, washers, flanges and custom forgings, so an anode assembly does not have to wait on a second supplier.

· Standards: ASTM B265 / B348 / F467 / F468, GB/T 2965, ISO 5832, DIN and JIS on request.

· Pre-sales engineering: we ask soil resistivity, coating holiday percentage, design current, pipe diameter and spool length before we quote a meter.

· Post-sales: same-heat reorder, coating-feedback loop, NCR replacement, photo-logged pre-shipment inspection.

Plain buyer language. RFX does not sell you "a coated strip." We sell the certified GR1 titanium foundation that a coater turns into a 30-year flexible anode — traceable from sponge to strip to buried ribbon. On a transmission main, the anode you cannot see is the one that decides whether the wire snaps in year 22. We make sure that anode starts with clean titanium.


7. Bottom Line

· Cylinder shielding broke conventional CP: a remote anode protects the can, not the wire on the far side, and the potential survey keeps reporting "protected" while wire breaks accumulate.

· The fix is continuous flexible MMO titanium ribbon on both sides: thin, bendable, 17 to 60 mA/m, 30 to 50 year life, laid in a 300 mm trench beside a live main.

· Baoji solved substrate, coating, joint and layout together: about 12 to 15 process patents released downstream at cost.

· The economics moved: unit cost down 30 to 45%, installation down 20 to 35%, lifecycle CP down 40 to 60% over 30 years, and export margins three times what commodity strip earns.

· RFX supplies the certified GR1 substrate behind the ribbon. That is the whole claim, and it is the one that holds up in a failure analysis.

Key takeaway. If a flexible anode quote arrives with no heat number, no coating-load report, no bend-radius test and no both-side layout drawing, it is not a 30-year PCCP anode. It is a strip with hopes.

 


RFX  ·  Titanium you can trace, anode substrate you can trust  ·  www.tiwwrfx.com


Electric Dirt Bike Performance Upgrades For Surron




References

[1] GB/T 33637-2025, Cathodic protection — MMO/Ti flexible anode (replaced GB/T 33637-2017, effective 1 May 2026). National Standards Information Public Service Platform. https://std.samr.gov.cn/gb/search/gbDetailed?id=4n69GHQ9tSk=&mode=p

[2] AWWA C304, Design of Prestressed Concrete Cylinder Pipe. American Water Works Association.

[3] AWWA M9, Concrete Pressure Pipe, 4th edition. American Water Works Association.

[4] NACE SP0169, Control of External Corrosion on Underground or Submerged Metallic Piping Systems. AMPP / NACE International.

[5] ASTM B265, Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate.

[6] Xylem, "Delivers actionable data to enhance the safety and resilience of a nuclear power plant" — electromagnetic (PipeWalker) inspection of 120-inch PCCP cooling-water lines. https://www.xylem.com/en-al/support/case-studies-white-papers/xylem-delivers-actionable-data-within-a-tight-time-frame-to-enhance-the-safety-and-resilience-of-a-nuclear-power-plant/

[7] Analysis of the effect of corrosion on the performance of prestressing wire and the role of cathodic protection in the Man-Made River project, Libyan Journal of Engineering Science and Technology. https://ljest.bsu.edu.ly/wp-content/uploads/2026/01/CSCE11.pdf

[8] 全周期视角下PCCP耐久性的影响因素与提升方法, Journal of China Institute of Water Resources and Hydropower Research, 2025. https://t4.sciengine.com/JCIWRHR/doi/10.13244/j.cnki.jiwhr.20250037


Previous: Stop Losing Deep-Sea Pipelines to Rust: How Grade-1 Titanium MMO Flexible Anodes Rewrote the Corrosion Playbook

Next: Why Flexible MMO Titanium Ribbon Anodes Finally Solved the “Shielding Dead Zone” Problem in Oil & Gas Tank Farms